© 2026 Autonomous Industrial Solutions, LLC All rights reserved.
FAQ
- WISPR Ground Control - FAQ
- Updating WISPR Ground Control
- Transferring Missions from Internal Storage to SD Card
- Pre-downloading Maps for Offline use and Terrain Follow
- Using Terrain Follow During Survey Mission
- Geofence use with Mission Planning
- Continuing a Mission after pausing mission or after hotswap
- Waypoint Mission Information
- How to Upload KML Files for Mission Plans
- Rally Points use with Mission Planning
- Mission Planning Basic Information
- Terrain Follow Basic Information
- Pre-Arm Errors and Fixes
- How to Disable auto-land with LiDAR Range Finder
- Changing SkyBoss controls with WISPR Ground Control
- Compass Calibration Information
- Remote ID (RID) Information
- How to Set Your UAS ID on WGC
- Tower Scan Wizard Information
- Monopole Tower Scan Information
- Guyed Tower Scan Information
- Flight Modes Information
- How to connect enable RTK
- WISPR24 Mapper FAQ
- I cannot install WGC using the install file. The script to install appears but stops and does not install WGC.
- When the WGC script runs, I get an error message that says USB debugging is not allowing the script to run.
- How to run PPK with WISPR Ground Control
- Guyed Tower Scan Informational Guide
- Monopole Structure Scan Informational Guide
- Panoramic Corridor Mission Informational Guide
- Panoramic Waypoint Mission Informational Guide
- Waypoint Missions Informational Guide
- WISPR Flight Firmware - FAQ
- SkyScout2 and SkyScout2+ - FAQ
- Download UBX file for SkyScout2 or SkyScout2+
- Quick Start SkyScout2
- Quick Start SkyScout2+
- If my SkyScout2 or SkyScout2+ is not flying smoothly, what should I do?
- Automatic Channel Selection Issue and Troubleshooting for SkyBoss with SkyScout2+
- How to use RTK and set geotagging with SkyScout2 and SkyScout2+
- Additional disarming/arming method with SkyScout2+ or Ranger Pro+
- Ranger Pro - FAQ
- Quick Start Ranger Pro
- What to do if cooling fans stop spinning
- My leg bracket connectors are becoming loose frequently. What should I do?
- Propeller Maintenance Information - Ranger Pro
- When attaching the landing gear, which way should the bracket for the antennas face?
- If my Ranger Pro is not flying smoothly, what should I do?
- SkyScout - FAQ
- Battery - FAQ
- Charging and Discharging - Ranger Pro Battery
- Hotswap - Ranger Pro Battery
- LED Indicators for SkyScout Smart Batteries
- Charging SkyScout Smart Batteries
- Firmware Update for SkyScout Smart Battery
- Failsafes SkyScout Smart Batteries
- Charging Questions for SkyScout Smart Batteries
- RMA Information for SkyScout Smart Batteries
- How to Hotswap SkyScout Smart batteries
- Why did I get battery disconnect issue when it seems like I had them inserted correctly?
- Payload - FAQ
- Sony ILX-LR1 version 1 boots up asking for Language Options Error
- How to convert a gpslog.txt from ILX-LR1 or WISPR24 Mapper for Pix4D
- Download UBX file for PPK with WISPR24 Mapper or Sony ILX-LR1
- Enable "Calibrate Gyro on boot" on ILX-LR1 or WISPR24 Gremsy Gimbals
- Enable "Calibrate Gyro on boot" for Gremsy Vio or Zio
- LiDAR Offsets for LiDAR Payloads
- Why is my LiDAR Calibration button not showing up although I have a LiDAR selected as a payload?
- When surveying with LiDAR, what coordinate datum should you use when using a PPK base?
- Laptop/Desktop Computer Hardware Requirements for Processing LiDAR data
- If the RESEPI XT32 is not showing a green button on the GNSS on the side of the LiDAR unit, what should I do?
- Where is the PPK image geotag information from the LiDAR payload?
- RTK-GNSS base recording best practices with LiDAR
- Why are there spaces in between my photos when watching my mission?
- Gremsy Vio Other Frequently Asked Questions
- I only have partial control with the Gremsy Vio.
- I have no roll wheel control on the Gremsy Vio.
- When I use the Gimbal Center button, I lose control of the gimbal afterwards with Gremsy Vio.
- UgCS Echosounder Bathymetry Payload - Frequently Asked Questions
- UgCS Laser Falcon Methane Detector - Frequently Asked Questions
- How to Auto-Tune your Gremsy Gimbal with ILX-LR1 and WISPR24MP Payloads
- How to balance Gremsy Gimbal for Sony ILX-LR1 and WISPR24 Payloads
- Sony ILX-LR1 - I selected ILX-LR1 payload and clicked reboot button but after rebooting the ILX-LR1 doesn't auto-clear language selection menu.
- Sony ILX-LR1 - My images are not present on my SD card from my mission
- Sony ILX-LR1 Version 1 - Why did my images not geotag?
- Sony ILX-LR1 Version 1 - Why did my first image taken not geotag but all others are geotagged?
- WISPR24 Mapper - Why did my first image taken not geotag but all others are geotagged?
- WISPR24 Mapper - Why did my images not geotag?
- WISPR24 Mapper - My images are not present on my SD card from my mission
- Gremsy Vio - Object Tracking Best Practices
- After My RESEPI Flight I Only See the Data Folder or No PCMP File
- Smart Controller - FAQ
- SkyBoss - FAQ
- How to retrieve Flight Logs from your SkyBoss
- Changing SkyBoss Button Mapping
- What should you do if the LED light is flashing red/solid red on your SkyBoss?
- If the SkyBoss is dropped or any damage is noticed what should I do?
- What percentage should my SkyBoss be charged to before flight.
- Automatic Channel Selection Issue and Troubleshooting for SkyBoss
- Additional disarming/arming method with SkyBoss Smart Controller
- Herelink Blue/Black - FAQ
- How to retrieve Flight Logs from Herelink Blue/Black
- What should you do if the LED light is flashing red/solid red on your Herelink Blue/Black?
- If the Herelink doesn’t load parameters when opening WISPR Ground Control, what could be wrong?
- My smart controller will not connect to my 5GHz network, what should I do?
- My controller will not connect to the Hotspot on my phone. What should I do?
- If the smart controller is dropped or any damage is noticed what should I do?
- What percentage should my Herelink be charged to before flight.
- What should I do if I try to arm my drone with the joystick and the “Calibration still running” error pops up, not allowing the drone to arm.
- What if my smart controller will not connect or show my Wi-Fi SSID?
- SkyBoss - FAQ
- General - FAQ
- WISPR Cloud - FAQ
- Untitled whiteboard 2026-07-02